After making a new purchase and bringing it home, you, unfortunately, discover the security tag was left on by the cashier. Thankfully, you do not have to go back to the store; you can remove a security tag from a security tag at home. Whether you have a magnetic or ink security tag, we have put up a comprehensive list of simple techniques for removing various sorts of metal tags in a secure and efficient manner. Continue reading to find a technique that will work for you, from employing rubber bands to magnets.
First Technique: Using Rubber Bands
Step 1:
Place the tag’s ink cartridge so that it is facing down. The portion of any brand’s custom metal tags that protrudes from the plastic is the ink cartridge.
Step 2:
To remove the tag-containing portion of the garment from the remainder of the garment, pull it apart. In order to prevent the clothing from being damaged as severely if the sensor fractures, move it as much away as you can.
Step 3:
To secure the security tag’s pin, wrap an elastic band around it. In order for it to fit all around the pin, the rubber band must be big, thick, and strong enough. The pin will become looser as a result.
Step 4:
One hand should be used to hold the bigger portion of the ink tag.
Step 5:
Using your other hand, remove the pin. The pins’ holding force ought to be sufficient to cause the pin to finally pop off or to separate readily from the tag’s support. If somehow the rubber band is not able to sufficiently loosen the tag, try again with more rubber bands.
Second Technique: Using a Screwdriver
Step 1:
The ink cartridge should be facing up as you lay the clothing item on the ground.
Step 2:
Place a very small flathead screwdriver along the raised square pyramid’s perimeter.
Step 3:
Firmly press down. The plastic should be pierced by this and lifted.
Step 4:
Continue popping the plastic’s edge up.
Step 5:
Take out the inner silver paper layer. The metal plate beneath it will be visible to you.
Step 6:
Raise one of the metallic arms holding the pin in place using the screwdriver.
Step 7:
By sliding it, take the pin off the tag. The tag ought to be removed by simply slipping the pin through the hole that is now open.
Third Technique: Using a Magnet
Step 1:
A powerful magnet should be located. Since the majority of tags are disabled in stores by electromagnetic equipment, you can opt for a hard disk drive magnet or perhaps a rarer earth magnet instead.
Step 2:
Affix the tag to the magnet with the dome facing out.
Step 3:
The tag ought to be removed by simply slipping the pin through the hole that is now open.
Fourth Technique: Freezing the Tag
Step 1: Freeze the garment containing the ink tag. Consider letting the clothing freeze overnight for the best effects.
Step 2: Cut the tag open. You can simply utilise your hands, pliers, or the elastic band technique. As ink cannot spill if it is frozen, doing this will prevent accidental ink spillage.
Fifth Technique: Hitting the Tag
Step 1:
Pull the tag from the garment a few times while being gentle. Approximately ten times should be sufficient to start to loosen the pin.
Step 2:
Find a big nail. The nail ought to be larger than the tag and have a head that is at least as big as a coin.
Step 3:
Remove the tag from the clothes by pulling it. Hold the tag’s long plastic portion out to the side.
Step 4:
Press the ink cartridge down until it springs open. Strike the ink cartridge repeatedly until it bursts open without using excessive force. For it to be done correctly, you might need to strike it thirty or more times. A powerful hit could cause the tag to pop open, so be cautious not to do that.
Sixth Technique: Using Needle-Nose Pliers
Step 1:
Grasp the security tag while the ink cartridge side is facing above.
Step 2:
Grab one of the rectangular tag’s sides with a set of pliers.
Step 3:
Use a new set of pliers to hold the tag’s other side.
Step 4:
The pliers should be used to gently bend the tag’s two sides down. Avoid bending too far or the tag might split in half and splatter ink all over.
Step 5:
Bend it again and again until it opens. The pin ought to pop off as a result of this loosening.
Seventh Method: Using Brute Force
Step 1:
To give the tag some slack, insert something between it and the pin’s head.
Step 2:
The pin must be bent back and forth repeatedly until it snaps.
Step 3:
To get the pin out of the hole it initially entered, pull the tag back straight.
Step 4:
Break the tag and open it.
Eighth Method: Burning the Tag
Step 1:
Use a lighter to burn the tag’s dome-shaped area. It will probably catch fire if burned for a short period of time because it is plastic.
Step 2:
Slice the dome with a blade or with any similar instrument.
Step 3:
A tag and spring will almost certainly pop out as you continue scooping in.
Conclusion
Certain things are given security tags by clothing retailers as a theft prevention technique. If you attempt to walk away with the security tag still attached to the item, an alarm will go off. If you attempt to remove the tag manually, some will also spill ink over the clothing, ruining it. As long as the tag is taken off just before you exit the store, this typically will not be a problem. However, occasionally checkout clerks may overlook a tag, or you may receive an online order for a shipped-from-store item only to discover that the person who packaged it left the tag on. Read the ways listed above and understand how to take off the tag on your own if you find yourself in this scenario.
